- Fits:
- YAMAHA SR500
- YAMAHA SR400
I bought it because I needed to replace the gasket when I overhauled the Manifold area.The paper quality is not bad and can be used just like OEM.good point● Easier to obtain than OEM.Durability is al...Read More - Fits:
- YAMAHA
- YAMAHA
The Engine's rotation was somewhat lighter.I thought the air pressure inside the Engine was working well or something like this. I don't get dramatic acceleration or anything like that, but I don't fe...Read More - Fits:
- YAMAHA SR400
- YAMAHA SR500
In the picture, both the Heat Radiation Fin and the first tier have the BORE ACE Logo, but in reality, there is nothing and it looks cheap.I don't think it absorbs enough heat to feel the effect eithe...Read More - Fits:
- YAMAHA
- YAMAHA
At first I considered the Manufacturer's Oil cooler here. But recently, I thought it was a little too large because I'm running slowly.Then I saw the Heat Radiation Fin for Oil TankDown tube in the Ma...Read More - Fits:
- YAMAHA
The manufacturer's Negative Pressure Adapter to this product The installation is very easy because of the Bolt On However, when 1 pc of an attached bolt is tightened about halfway, it suddenly becomes...Read More - Fits:
- YAMAHA SR500
- YAMAHA SR400
It is a fin for better heat dissipation of the Camshaft CoverTo install the Heat Radiation FinBody, remove the Porto and Pipe and Just insert it into the Camshaft Cover from the side, fit the Pipe and...Read More - Although installation is possible without taking down the tank, it is Large strange to put in L-TypeWrench I struggle withThe Short Neck L-TypeWrench makes installation quite easyI bought it for the m...Read More
- Fits:
- YAMAHA SR400
- YAMAHA SR500
It looks very clean and the silver shine matches the SR400! I think the silver shine is also suitable for the SR400!You'll need a Glasses Wrench, but it's easy to install(The size of the original Nut ...Read More - Fits:
- YAMAHA SR
I bought this product because the Idle Screw of the FCR Carburetor Body is difficult to useIt is easy to install and securely attached to the carburetorHowever, the Screw and the bottom screw of the F...Read More - Fits:
- YAMAHA SR400
- YAMAHA SR500
If you use the FCR Carburetor Body Carburetor as you bought it You can install the throttle wire and remove it by simply removing the lock nut You canWhen working on setting up Carburetor, the frequen...Read More - Fits:
- YAMAHA SR
I've driven it for 30 years without any major breakdowns, and I wanted to do something Engine friendly I thought about it and after much searching I came across this Oil lineI don't feel a large chang...Read More - Fits:
- YAMAHA
I use the Assist system of Parts from Boa Ace's Parts, and to be honest, it works (Change) It seems that some of them have and some of them are getting worse One of the obvious changes is this Intake ...Read More - Fits:
- YAMAHA SR
Thanks to this product, I was able to install the CR without any troubleThe Instruction Manual is also very helpfulI use it with a negative pressure adapter and there is no problem at allRead More - Fits:
- YAMAHA SR400
- YAMAHA SR500
At the same time we installed Heat Radiation Fin of the 1st stage and the 2nd stage. Installation is easy, but it is regrettable that Torque of Nut tightening was not described in Instruction Manual. ...Read More - Fits:
- YAMAHA SR400
- YAMAHA SR500
Installation is easy. I run the same Route at the usual temperature and the oil temperature is 5 to 10 degrees lower. We installed Heat Radiation Fin attached to Cylinder head at the same time, so we ...Read More - Fits:
- YAMAHA SR
I bought it to install CR 38 of WM.I am satisfied that carburetor can be exchanged cleanly without interfering with FrameHowever, even if O-ring that sandwiches Manifold and Flange is too fat or Bolt ...Read More - Fits:
- YAMAHA SR
If there is enough skill to remove Normal cab, it will easily take youNegative pressure is explained to be connected to Fuel Cock, but I dared to connect to Air inductorSince there is no choice, Fuel ...Read More - Fits:
- YAMAHA SR
The goodness of construction is a falling stone Decompression lever.I wanted to refresh around the Handlebar, and I only made Lever by excluding Wire at the same time as product announcement.He seemed...Read More - Fits:
- YAMAHA SR
I bought it because the price was reasonable and interesting. You can easily do the work itself by removing Wiring from Connector and letting Spark Assist interrupt instead. When installing Engine aft...Read More - Fits:
- YAMAHA SR
【What made you decide the purchase?】Net and Impression【How was it actually used?】According to the reputation, the vibration of the engine got mellowed overall. The paste of Speed ??has improved better...Read More
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING