-08-8(Carburetor)*Drilling of switch hole is required|*You can use stock side cap. |*It is necessary to change the direction of the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
GSX400
05-07 GK7CA *Processing of the switch hole is required|* You can use the normal side cap.
Made in Japan.Prototype, installation confirmation and mass production are all under in-house management.These handlebars are made with a great deal of care and attention to detail, including careful selection of materials, several types of polishing, engraving of part numbers, high-precision bending and welding, and high-quality surface treatment, based on technology and know-how cultivated over many years in Osaka in Japan.STKM13A steel material with excellent tensile strength is used.Cleared by JMCA safety standard value.Triple nickel and chrome plating (3 layers of nickel and chrome) finish with thick film and excellent durability and corrosion resistance.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I've been using the EZ-FIT-Bar, but I just need a little more height! And greedy I purchased this product The quality is good with no plating irregularities and no surface scratches 400ccClass for Replacement compatible Pipe Handlebar I think the width is just right for the However, this width seems to be narrow when it is W800 used this time, and it becomes a tight position around the shoulder I ended up having to go back to the EZ-FIT-Bar I bought last time Well, it's a MotorcycleParts-esque story As for the products themselves, they manufacture and sell a wide variety of Pipe Handlebar It's only HURRICANE Very good product quality and I would recommend it to anyone That's why I was a little disappointed (Lol) View Detail
ZEPHYR750 (2001 type) I bought it because the OEMHandlebar was a little crooked. The Handlebar I bought this time is a nice feeling, but there may be shapes to fit more. Since this Manufacturer is rich in variety, I plan to exchange Handlebar several times and search for Best position while getting on in the future.View Detail
Fits: HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC II* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Been using this handlebar for a few months and it is much better than my previous wide handlebar. The sweep back angle and height brings the handlebar closer to my body and easier for maneuvering. The shorter length from end to end and the sweep back angle towards me makes it alot more easier for lane splitting. All in all better posture and handling for urban riding. View Detail
Fits: HONDA CB400SUPER BOLDOR 05-07 NC39 *Processing of switch hole required|* Required side cap (for 18mm diameter), HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC II* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
Since it was 163 cm and Small handle, I felt Handlebar was a bit far and low, so I exchanged it. Harness and Wire had plenty of time, but since Brake hose was feeling Limit even at NORMAL, I searched for the range where the Large Year Position does not change and made it to this Handlebar. Because it is a Universal Product, install mounting hole of vibration proof material Quantity : Pair (for Left and Right) Quantity Pin hole of Switch box with 2 places : Pair (for Left and Right) You need to be able to open one place at a time. The dimensions from the end and the vibration isolating material mounting hole are Quantity : 2pc. Care must be taken so that the hole position of Set is 180 degrees relationship. The position of the hole in the Switch box, after positioning the Handlebar and Lever correctly, put Pin in red and marked the Handlebar and opened it. I did not need it because it was remodeling so that the parking brake can be operated with Lever, but NORMAL also needs to open the pin hole of the bar KingBrake. Brake hose was in a state of being sticking unless you remove what is fixed at the Upper clamp. I thought that Grip is ahead better, but I think that it is impossible to replace Brake hose any further, because it is ABS, so I am not confident of bleeding at the time of replacement.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!