*Use the Setting Main Jet or Setting Main Jet Set separately.
●For those who want to install a big carburetor but are worried about rain and intake noise Big carburetor kit that allows use of stock cleaner ●Necessities for Big Bored vehicles
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I decided to Bore up on the SUPER CUB 90 to make it a little easier for me to go camping with it!
I bought it because with Bore up, the NORMAL carburetor could no longer support the setting. The air cleaner side can be installed in a NORMAL state, but as it is, there is not much air to breathe. I also changed the Filter and adjusted the Big Cab because I couldn't make the most of it.View Detail
[Was there anything that disappointed you? Generally satisfied However, there are two points that require improvement in the design, as described below
Do you have any wishes or improvements you would like to make for the Manufacturer? The accuracy of the joint parts of Carburetor and Manifold is similar to KITACO and others It's not a good comparison, so Material:It would be good to improve on Plastic's same etc. products
I don't know if it's the effect of individual differences, but the height of the Manifold is lower than the height of the Air cleaner The frame attachment part is lowered, so we had to lift it up I think the Clearance setting with the vehicle needs to be improved
[Do you have any products to compare it to? SP Takekawa PB16Big Carburetor I chose this product because of the price difference
What made you decide to buy? I wanted to keep the intake noise quiet, so I could use the NORMAL air cleaner and I like the fact that the NORMAL Choke Lever can be used as is The price is also a decisive factor in comparison to the SP Mukawa PB16, which is about 60% less expensive
How was your experience with it? The synergy of Bore up and other factors has clearly increased the horsepower But maybe it's just a characteristic of this Carburetor, or maybe it's just that the Engine can't restart after it's fully warmed up The Engine won't start unless you adjust the Timing and open the Throttle a bit, which is a habit Impression (It didn't take nearly as long for a single KICK to take place.) I wish I could improve it in Settings...
Was the installation difficult? It's as easy as the Instruction Manual
【Please tell me the installation point and hang】 When you remove the carburetor from the carburetor in use, you need to set the bolts to the fuel hose If you don't do this, Gasoline will keep coming out until the tank is empty, so you must do this beforehand
[Was the Instruction Manual easy to understand? There is no shortage of content to install
[Included Parts:were they on? Gasket and other necessary items are available
[Others] For the porting of the head for performance, Manifold has been designed by KITACO for PC20View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!