Manufacturer: Endurance 1 month (or up to 1000km of driving distance after installation) Installation time:0.3h Material: Iron (black paint finish) Product Description: Refer to the instruction manual
*Please note that the Endurance in-house test is a comparison based on certain conditions and is not the same as the guarantee or conditions in actual use.(Loading capacity and stability conditions vary depending on the carrier used and the location of where the bike is parked.) *In case of installing it on together with Endurance rear suspension (see recommended products), the vehicle height will be lowered and the inclination of the vehicle will be shallower (about 9.5 degrees), so please pay attention to the inclination of the place where the vehicle is parked and make sure the vehicle is stable before use. *Because the stability of this product varies depending on the inclination of the stopping place and loading conditions, please make sure that the vehicle is stable before using this product. *This product is designed for stock vehicles, so Endurance does not recommend using it for vehicles that have been modified in terms of ride height.
*The installation of models is not checked other than those listed in the compatibility check list.If your vehicle is not listed, it cannot be installed or has not been tested. *The installation of the product to the models that are not listed in the compatibility check list is not guaranteed. *The color of the product may vary depending on the shooting conditions, monitor, product lot, and left and right of the set product, but returns or exchanges is not accepted. *There may be changes in product specifications due to the manufacturer's reasons.
The "right side stand" is a standard feature of CT125 and HUNTER CUB
It is not only convenient when the inclination of the ground is uneven, or when the inclination does not match with the neighboring bikes because they are facing different directions It's not enough to just have it on the right side,
It is designed to be as stable and strong as a reinforced side stand as being loaded on a carrier, In addition to the extra thick bracket brackets, the side stand ground position and vehicle tilt is adjusted!
In addition, the bracket position is set as far up as possible to secure the minimum ground clearance when the side stand is stored so as not to spoil the characteristics of HUNTER CUB.
In the in-house Endurance test, the bike was parked on the right side stand on flat concrete When the vehicle was loaded with 50kg, the stock side stand caused the front tire to lift and the vehicle to fall over.
It can also be used with the CT125 reinforced side stand bracket.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
The finish of the bracket and STAND is perfect, and the STANDBOLT nut and springs are Honda OEM parts. The rearward offset makes it difficult to fall over even when the rear box is fully loaded with luggage. I use it with reinforced STANDBracket and it is very useful!View Detail
On a slope such as a forest road "I'll stop. or as an auxiliary STAND on soft surfaces.
Was the one you received as per Image?
Image is correct. The strength is enough.
Was the installation difficult?
If you follow the manual, you will not fail. The tightening torque is also listed and easy to understand.
How was your experience with it?
It extends from a little behind the footpeg and has high stability on hard ground such as Asphalt. If you try to STAND while seated, you'll almost step on the Kick pedal.
[Included Parts:were they on?
All the necessary bolts are included, GCraft's Right Side Stand was released earlier but it did not include STANDArm. This product is all-in-one and easy to understand. Don't forget to use the grease on the pipod.
[Was there anything that disappointed you?
The ”foot” of the STAND is the same as the NC750 series, and the area is small, and it is a little uneasy on the soft road surface. The stand plate (extended plate) for NC750 can be installed to increase the area of the foot, but the extended plate interferes with the center stand because the clearance between the center stand and the plate is tight.
Other items that would be helpful Installation points and hang/Availability and clarity of the Instruction Manual/Points to consider/Items to purchase/Opinions and requests to the Manufacturer
It's also the fact that it was on a CT110. "I wonder what it's like. I was curious about this, but I was very satisfied with the practicality.
It is regrettable that the area of ”foot”of STAND is too small. I think that many people who want to attach the Right Side Stand like this product to the rider's use scene are those who drive on the dirt with full of camping gear and stop on the soft ground for camping. It would have been better if the area of the ”foot”was larger and less likely to sink on soft surfaces.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!