Once you select the option, estimate delivery time will be displayed.
*Shipping date and Estimate time of arrival are not guarantee.
Once your orders are placed, we will check the stock of manufacturer and send you the confirmed Shipping time via e-mail.
[Material] ・Main pipe: 80 x 40mm figure of merit cross section (7N01 material) ・Axle block: A5083S material
[Weight] Approx. 4. 82kg (Stock: 7.02kg)
[Specification] ・Stock dimensions (for stock wheel & tire size) ・Stock chain cover can be installed ・Bearing specifications (included) ・Stand hook collar included (M8)
*There may be changes in product specifications due to the manufacturer's reasons.
By using 80x40 cross section pipe for the main pipe, it is lightweight and has moderate bite. In addition, the layout of the main arm is carefully designed, and the same figure of the right side is adopted. It is reproduced by combining the triple square pipe and machined aluminum parts to ensure high rigidity and strength. This allows you to use the OVER megaphone exhaust or the stock exhaust. The weight is reduced by about 30% compared to stock, and the feedback from the road surface is easily transmitted by the weight reduction under the springs, so you can enjoy more aggressive cornering.
Points of Attention
* If there may be an instruction manual included, it will be written in Japanese.
I bought this to lighten the weight. As for the performance, I think the setting of the suspension is inevitable.
The initial of rear suspension is in the shipping state. The impact of fine bumps on the road surface can be quite severe. Therefore, the Initial of the Rear suspension is lowered by one. (The weakest) I did. This has improved things a bit, so I'll be operating with this for a while for now. Since NITRON and OVER are collaborating, we would like to exchange the rear suspension someday. Even though the weight has been reduced by 2kg, the effect on speed cannot be felt.
I would have liked the color Black, but I went to the trouble of UpCHARGE. In case you don't like the product itself, worry about it. Material in terms of price:I chose Polishing. It's a two-step process, but if I like it after using it for a while, I'll send it out for painting myself. That said, I was surprised by the mirror finish, which was more than I expected. Catalogue image is a complete lie. (Lol) However, since scratches will soon appear, the Swing Arm can be used with the color of your choice. Hard, thick coating (Powder coating) I like the If you like mirrored surfaces, you'll be happy with the results.
The replacement process takes a full day for a hobbyist. What was difficult was the structure of the swing arm pivot. It is difficult to understand the expression even if you look at the service manual. You need to understand the purpose and structure of Parts before you can work with it. The structure here is only sandwiched between the Long shaftBolt and Nut in the Off car ... . The disassembly and assembly of the Suspension and LINK was no problem because I had replaced the Link Plate in the past. You will need to hang the Frame from the top, so you will need a tool for that. You can support it from the bottom by using the pedal part.
On the downside.
The accuracy of Rear Fender mounting Bracket is not good. The Fender has two Left Side and one Right Side Bolt, while the OEM has one Clip fastener on the Right. This is not there. And the position of the Right Side Bracket. (or angle) feeling sick Fender will be slanted. The Chain Cover is straight against the Chain so it seems to be a Right Side issue only. I bent it by hand and it was a little better, but I didn't want to do too much and break it, so I don't do that anymore.
Then there's the fact that the Hose clamp part of the Brake and the part where the Hose guide is attached are missing. If you try to remove the Hose guide, it has already passed through the Hose, so you have to remove the Hose once or You will have to break the Guide. Or the Right Side FenderFixing Screw hole. I'm thinking of making a simple Plate to hold the Guide.... It seems to me that you'd have to do that and be able to fix the Hose in at least one place to be dangerous. This is for road use. (Not for competition) Isn't it? This is not mentioned in the product description or in the Instruction Manual.
I used the OEMHose guide as is with the Fender Clip holes.
The Merit of the most Large by attaching Swing Arm is because I bought it dividing it as a weight saving. I'm satisfied with it, but I think it's not a good product. There should be an explanation, especially regarding the installation of the Hose.View Detail
* The BEST and MUST store to find Japanese parts. * Register now for amazing deals and other special offers! *Over 800,000 listed items. It's hard NOT to find your parts.
SIGN IN TO WEBIKE JAPAN
Please enter email at least 6 characters.
Please enter a valid email address.
Email is already in use.
Your account has been banned.
Email address and/or password is not match.
Authentication with facebook fail.Please try again.
Please select How did you get to know about Webike Japan?
OR
YOUR ACCOUNT HAS BEEN CREATED!
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
Get on your grid by register your motorcycle! About our "Mybike" service
"Easier to Search Items" It helps you to search items to fit for your motorcycle!
"Get Much Valuable Information" It helps you to get special deals, newly listed items and closeouts about your motorcycle!
"Easy to Register" It requires only your motorcycle manufacturer, model name and model year!