Awesome variator! Left hand side is the Kitaco Pulley whereas on the right is the original pulley. You can see a big difference between the 2 especially with the diameter. Great degree on the pulley! give you more rpm on low and pulls hard. you can cruise along on 5ok's with minimal throttle squeeze. Really happy with your product! Next project is the torque cam so that i can utilise the whole pulley. Cheers!
Fits: YAMAHA Remote controller jog 5SW All models, YAMAHA Remote controller jog 5SU4, YAMAHA Remote controller jog 5SU1-4, YAMAHA Remote controller jog 5SU1, YAMAHA Remote controller jog 5PT All models
Вариатор очень хорошего качества, диаметр самого вариатора и ответной щеки 98мм. Очень лёгкий с сравнением с родным вариатором. При правильной настройке ремень выходит на полный радиус и мой скутер едет 92 км/ч при оборотах двигателя 9000 об. Вес роликов которые я поставил 4.5 г. The variator is very good quality, the diameter of the variator and the response cheek 98mm. Very easy to compare with the native variator. With the correct setting, the belt goes to full radius and my scooter goes 92 km / h at 9000 rpm. The weight of the rollers that I put 4.5 gView Detail
Fits: YAMAHA Remote controller jog 5SW All models, YAMAHA Remote controller jog 5SU4, YAMAHA Remote controller jog 5SU1-4, YAMAHA Remote controller jog 5SU1, YAMAHA Remote controller jog 5PT All models
Bought this for my 2007 cv50 Yamaha jog with 5su engine. Feel like the description of the variator is a bit misleading. Says power drive kit for more acceleration which was not the case. The stock variator gave better acceleration from 0-40 however the Kitaco variator really comes into its own once you get past 40kms, lots of power and torque to keep you accelerating beyond 60kmns. Also can cruise at 50kms at 1/4 throttle. So in short more for top speed rather than acceleration. Acceleration does not improve at all even with lighter rollers.View Detail
Fits: YAMAHA Remote controller jog 5SW All models, YAMAHA Remote controller jog 5SU4, YAMAHA Remote controller jog 5SU1-4, YAMAHA Remote controller jog 5SU1, YAMAHA Remote controller jog 5PT All models
First of all, check it by pontificating
Slightly increased maximum speed from OEM status
Acceleration is more than the OEM because the shifting is too advanced It's a little dull I felt that
There seemed to be plenty of room on the Clutch Side, so I was able to get the Other Brand Product I added a 0.5mm clutch offset washer and dropped it in
If you add the Clutch offset washer, the Clutch outer will be It may come in contact with the clutch nut
You can choose to use the Clutch nut from Other Brand Product's Small Dice or You will need to use a washer or other means to release the Clutch outer
After setting up the weight roller and replacing it with a new OEMBelt, the acceleration is It is the same as the OEM condition, OEM + 10km/h extended
In my case, I use Tachometer and use the Power band to shift gears Setting
The Weight roller fits the setting for a 3 to 6 gram weight reduction
This Drive kit also comes with a Large shaped Face to match the Pulley I think it's a Kit that can aim for the highest speedView Detail
Fits: YAMAHA Remote controller jog 5SW All models, YAMAHA Remote controller jog 5SU4, YAMAHA Remote controller jog 5SU1-4, YAMAHA Remote controller jog 5SU1, YAMAHA Remote controller jog 5PT All models
OEMPulley&The size is larger than the Face, so you can expect a maximum speed It was, so I bought it
I think this price with Face is a bargain
When I checked the car with it completely ponied up without any setting, the acceleration was good and the top speed was good It grew slightly
And if you remove the Washer, which is an OEM addition to the Pulley boss, the acceleration is so-so It feels like it extends to the top speed of OEMPlus 10km/h
Adjust the weight roller, make the Belt new, and drop the Clutch into the (KN Planning Clutch Off-set Washer is a Recommendation) If you go
It's going to be good, along with acceleration and top speed
I'm sure there are individual differences, but in my case, the KN Planning Clutch Off-set Washer 0. Clutch outer interfered slightly when I put in 0.5mm
OEM Clutch nut (OEM number) for the Smaller HondaDIO in Nut outline (90202-187-000) and there was no interference when I replaced it with a new one (90202-187-000)
In addition, since Pulley seems to have a wide range of settings, it is possible to use it in different ways depending on the settings You can expect to go up to 20km/h on the OEMPlus
If you want to increase your top speed, strengthen your High grip tire or Brake If possible, you should also consider suspension reinforcement and overhaul
It may be an exaggeration, but NORMAL is 30km/h Plus&alpha of the legal speed Consider that it was only designed in ;
Even though modifying and driving is your responsibility, it doesn't mean anything if you cause an accident
Even if we're not driving un-Brown, I've been high on a number of occasions when I've jumped out of the side road in a sudden burst of traffic The grip tire saved my life
Please take a look at itView Detail
Fits: YAMAHA Remote controller jog 5SW All models, YAMAHA Remote controller jog 5SU4, YAMAHA Remote controller jog 5SU1-4, YAMAHA Remote controller jog 5SU1, YAMAHA Remote controller jog 5PT All models
Vino (SA10J 5AU) We mounted on.
It is an exchange from B company High Speed ??Pulley.
First of all, it does not come with a Kaname's back plate.
It is diverted from Pulley for KITACO made vertical engine.
Weight Roller tried heavily, with 3 Grams 6 pieces,
Set Ing decided.
Feeling that it ran. Zero I will pull the guy from the departure,
The elongation in the high speed range is not so good.
As the low and medium speed range accelerates pleasantly from any rotation speed,
Town ride became fun. Just open the Axel lightly.
If I did not ask for absolute maximum speed, it seemed like a good product.
Exclusive Back plate not included is missing.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING