I do not understand OEM's feeling of use (Since it was exchanged before car delivery) I do not feel the wind from the front, so I think that it is the correct answer. I am concerned about the wind-in wind on the knee, so I am searching for Side visor.
I was attaching GIVI's Long Screen to 125 cc Scooter I was riding all the time.
This time I changed to FORZASi and I was surprised by the sound of Wind Cutting.
OEM's Long Screen is not high enough and I think that it is almost useless.
This Fabri Screen has almost completely eliminated the Wind Cutting sound, it is wonderful.
For details see fC 2 Know-how, "How to eliminate Helmet's Wind Cutting sound" I am writing an article saying.View Detail
Look at other people's comments
Although prepared and purchased,
It was pretty difficult....
Before struggling story, "In stock" Nevertheless, for two months for delivery
Inquiring,
There was a problem with System...
Be amazed.
○ Installation time = 2 days.
Contents of hardship
first day - - The installation target was 30 minutes, but even 90 minutes it was useless = tired so next day..
Day 2 - - Feeling newly, when looking closely, the position of the hole was Deta Lame.
In the Instruction Manual, "Hold the Screen top with your hand, while putting a little effort"
further, "While paralleling the mounting surface between Screen and the car body Bolt side"
Although attention points are written, with the momentum to break, even if you align the holes, it will not enter!
I went by two people, but it was impossible to concurrently!
I can only think that the design drawing at the production stage is incorrect!
It is not good unless you forcibly insert Bolt,
Three of the car body side Screw holes in four places, and the mountain of Screw attached collapsed!
Somehow, with oil and File Cliff, holes and Screw restored.
I tried it about 10 times but it was impossible..
As others have commented on, more than 1 cm is Gap!
In Screen's 4 places, cut the hole about twice as much as the original, finally installed!
After installation, somewhere in Screen seems to hit Front mask
I can not bear it smoothly!
A bad point - - - As stated above, installation is hard and absolute design mistake!
Good point - - Because Windshield is long both vertically and horizontally, windproof effect is absolutely Large!
○ Effect on driving - - - Actually, opening the Helmet shield does not feel the wind!
(160 cm tall) (In the past, the wind was hit hard enough to breathe... )
○ Cost surface - - - Approximately 13,000 yen is cheap, but it is a feeling that it is expensive as it was hard to install.
○ Strength surface - - - Because the strength has decreased by expanding the hole, it may be broken in 3 to 4 years...
〇 Do you recommend to others? - - - I think that it is better not to buy.
For ordinary people, I can not install easily, I get Shock,
It's a waste of time.
But, I have been able to use it for 3 to 4 years, things with better shape than this
If not,
I think I will purchase it again.
View Detail
Removal at the time of Valve replacement, broken by mounting.
It was a lifetime of 2 months.
That's too bad.
Polycarbonate's OEMLong seems to be better.
There is no choice..View Detail
When changing Valves of Headlight, it was removed, it was broken by wearing.
As a result, Polycarbonate Screen seemed better.
What is the lifetime of just 2 months? - - - -
I'm sorry.View Detail
OEMScreen makes it nearly 30,000 yen so I made it to Screen here. Windproof effect is outstanding. I do not need Knuckle guard.
It was a little disappointing as the price fell as soon as I bought it.View Detail
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING